Energy Efficient Windows in CT are installed by first removing the old wood sash windows and prepared the opening for the vinyl replacement windows. There is no need to disturb the interior casings when doing this, all that is required is to remove the interior trim stop on the inside jamb and the center parting stop witch will allow the two sash to be removed easily.

 Now it is time to install your new windows. You ought to have somebody there to help when doing the installation.   First, Remove all shipping materials from the window. You want to put the window into the opening to make certain it will fit, then remove it and run a bead of caulk on the face of the outside blind stop where the window will rest. You do not want to caulk, only to find out the windows are too large. It's worth the additional few minutes to make certain it will fit. Lift the energy efficient window and set the bottom in first. Then raise the top till it rests against the outside blind stops. Infrequently, when raising the top into position, the window frame will hit the pinnacle of the wood frame. You want to tap down on top of the vinyl frame while keeping pressure toward the outside. After you establish that it may fit, take away the new energy efficient window and put it aside. Run a bead of caulk on the face of the outside blind stops to form a seal against drafts. I prefer 100% silicone caulk for the most energy efficiency. Raise the window into position again. Now have your aid hold the window in position while you raise and lower the sashes, making certain the window is square in the opening. Installing Energy Efficient Windows in CT are a great investment but you must make sure that they are sealed and installed properly to make sure they will perform properly and save you energy for years to come. Don't hesitate to hire a professional Replacement Window Contractor in CT if you are not comfortable doing it yourself. You can also consult with a window contractor to see what a quality energy efficient window

Remember how you ordered the windows three / 16'- 0.25 ' shorter than the tightest measurement? Here is where you use this space to adjust the frame to be the most plumb and level. Get a box of popsicle sticks and wood coffee stirrers at the food store. The coffee stirrers are about one / 16' thick, and the popsicle sticks are roughly twice as thick. You would like to put the shims in the 4 corners. Then caulk the opening on either side and along the top before installing the interior stops. I do not counsel putting any screws in the sides, but you can put one screw in the top center and one in the bottom center. You do not have to use any screws in this type of installation, since the shims will eliminate any side play, and the caulk on the blind stops will hold the frame in place too.
Remember, we still have to re-install the interior stops. Before installing the interior stops, remove all of the old nails and replace them with new nails.

A 1'- one quarter ' finish nail is fine. Before installing the interior stops, scrape all old caulk off the stops. If the window has four stops, install the shortest ones first. That way it's possible you can bend the longer stops into place between the 2 short ones. Employ a nail punch to sink the head past the outer surface of the stop.

If you have 1 or 2 windows to do, I advise doing the 1st window to this point before going to the next.

How annoying would it be to have an assistant removing the old sashes, only to find out the windows are not going to fit.  If the 1st one goes in fine, then you can send your aid before you to begin removing old sashes. The right way to bypass the nightmare of having some new windows that will not fit is to be sure you measure In the correct way. Remember, tight minus 0.25 ' on the width and height should be fine. Finish the interior by caulking the area of the interior stop where it meets the surrounding, and the point at which the stop meets the new frame. Fill the nail holes in the interior stops with caulk to cover the nail heads. Now it is time to finish the outside.

If you purchase a lower grade window that does not come with anything to fill the opening beneath, you can purchase some wood trim to fill the space, or it is possible to get a flat vinyl trim that fixes to the face of the base of the new frame. When you cover the bottom opening, it is time to caulk where the outside blind stops meet the vinyl frame, and where the bottom opening filler meets the wood sill. That is it! You are done! You should buy accessories to cover your old wood sills with a vinyl wrap extrusion. That may also be found on the internet site under the 'purchase trim' tab. 

Get a professional factory direct estimate on  Energy Efficient Windows in CT for a Price Your Window preferred window contractor.

 


Comments




Leave a Reply


Google Analytics Alternative